Phần mềm MasterCAM X5 Full 32/64bit


Ở bài viết này mình xin giới thiệu bản cài đặt đầy đủ của phần mềm MasterCAM X5 link tải google drive.

Link tải

Tải về bản cài và thuốc: Tại đây

Link dự phòng (Mshare):     Tại đây

Pass giải nén (nếu có): pro100share.win


Hướng dẫn cài đặt


MasterCAM X5 32bit :
ATTENTION!ATTENTION!If you already have USB-Emulator for MC X4 (HASP or NetHASP) installed you can skip steps 1) – 5) and need only to run “mastercam_X5_crk.exe”
1) Unpack a folders “USB-Emul_Win32” and “remove_old_emuls” to your computer1) Unpack a folders “USB-Emul_Win32” and “remove_old_emuls” to your computer
2) Run “remove_old_emuls\delete_old_emuls.bat” to CLEAR a Windows Registry from “blacklisted” Emulators
3) Run “mcamX4_MU3-dealer-nethasp.reg” or “mcamX4_MU3-industrial-nethasp.reg” (dealer dump has got extended functionality!) if you want to install Mastercam X5 with NetHASP SIM type. orrun “mcamX4_MU3-dealer_hasp.reg” if you want to install Mastercam X5 with HASP SIM type.
4) Run “install.bat” to install USB-Emulator
5) Install MC X5 as HASP or NetHASP SIM type.
6) Copy Mastercam.exe from thuoc to <Mastercam X5 progdir> and replace original one
7) Enjoy

MasterCAM X5 64bit :
ATTENTION!ATTENTION!If you already have USB-Emulator for MC X4 (HASP or NetHASP) installed you can skip steps 1) – 5) and need only to run “mastercam_X5_crk.exe”
1) Unpack a folders “USB-Emul_Win64” and “remove_old_emuls” to your computer
2) Run “remove_old_emuls\delete_old_emuls.bat” to CLEAR a Windows Registry from “blacklisted” Emulators
3) Run “mcamX4_MU3-dealer-nethasp.reg” or “mcamX4_MU3-industrial-nethasp.reg” (dealer dump has got extended functionality!) if you want to install Mastercam X5 with NetHASP SIM type. orrun “mcamX4_MU3-dealer_hasp.reg” if you want to install Mastercam X5 with HASP SIM type.
4) Install a USB-Win64 Emulator
You need a local Administrator rights to install this emulator for Win64!On Windows Vista64 and Windows7 64-bit you need to boot Windows in mode F8 > Desable Unsigned Drivers Enforcment !!!
4.1. Reboot computer (for Windows Vista64 and Windows7 64-bit you need to boot Windows in mode F8 > Desable Unsigned Drivers Enforcment !!!)4.2. Install usb-emulator drivers Start -> Control Panel -> Add Hardware (Yes, I have already connected the hardware) -> Add a new hardware device -> Install the hardware that I manually select from a list -> Show all Devices -> Have disk -> Browse -> (browse to folder “USB-Emul_Win64”) -> OK -> Confirm to install not certificated drivers if Windows ask for..
If setup is succesco you have to see new system device:Device Manager -> System devices -> Virtual Usb Bus Enumerator
5) Install MC X5 as HASP or NetHASP SIM type.
6) Copy Mastercam.exe from thuoc to <Mastercam X5 progdir> and replace original one
7) Enjoy
Video hướng dẫn